I did this for a laugh and to see if it would work, no reason why it shouldn’t. I had a new bathroom fitted recently and the joiner had a load of decent off cuts that he left me. 18mm marine ply and s...

@koendb Right, quick run down. You should buy the compressor with biggest tank you can afford and with the highest CFM (cubic feet per minute) rating. Also, stay clear of HVLP spray guns if you are b...

Then I used the router and binding jig with a flush cut bit to trim the back and soundboard flush with the sides. Attachment : PXL_20230303_101356804.jpg Attachment : PXL_20230303_095651325...

Then I glued on the soundboard using the go-bar deck again. Attachment : PXL_20230302_120354103.jpg Attachment : PXL_20230302_121124041.jpg 🎶🎸🙏🙂

Then I marked out and cut out the notches to accommodate the braces of the soundboard. Attachment : PXL_20230224_115500427.jpg Attachment : PXL_20230224_115440900.jpg ......... Attach...

Next I cut out the notches in the kerfed lining to accommodate the back braces ready to glue on the back of the guitar. Attachment : PXL_20230209_142156708.jpg Then glued on the back using the ...

Then finished off using a sanding stick. Attachment : PXL_20221223_112230715.jpg Attachment : PXL_20221223_112239128.jpg ........ Attachment : PXL_20230202_134808725.jpg Attach...

Then gouged out using chisels. Attachment : PXL_20221222_152643727.jpg Attachment : PXL_20221222_152200582.jpg 🎶🎸🙏🙂

I cut out the edges using my Japanese saw. Attachment : PXL_20221222_143051515.jpg Attachment : PXL_20221222_143123547.jpg 🙂🙏🎸🎶

Next I marked out the dovetail. Attachment : PXL_20221222_141219576.jpg Attachment : PXL_20221222_141231194.jpg 🎶🎸🙏🙂

Then I had to radius the top edge and the back edge again. Attachment : PXL_20221130_153119512.jpg Attachment : PXL_20221130_154528941.jpg 🎶🎸🙏🙂

Next I glued the kerfed lining onto the edges of both sides. Attachment : PXL_20221118_130132369.jpg Attachment : PXL_20221125_110738336.jpg 🙂🙏🎸🎶

Then I cut the kerf into the strips using the kerfed lining jig on the bandsaw. Attachment : PXL_20221118_091601449.jpg Attachment : PXL_20221118_091944101.jpg 🎶🎸🙏...

Next I prepared the strips of wood for the Kerfed lining. Attachment : PXL_20221104_132319153.jpg Attachment : PXL_20221104_152410508.jpg Attachment : PXL_20221109_151125917.jpg &...

Once the sides and blocks were glued together I radiused the edges of the sides on the radius dishes. 28' for the edge to be glued to the soundboard.... Attachment : PXL_20221118_101450916.jpg ...

Then I glued them in place inside the mould Attachment : PXL_20221117_140936288.jpg Attachment : PXL_20221117_140927620.jpg 🙏🎶🎸🙂

Then I cut the end block and the heel block to size and squared them up. Attachment : PXL_20220916_144517215.jpg Attachment : PXL_20220916_143044686.jpg 🙂🎸🎶...

Then I bent the sides into shape using the pipe bender. I then held them in place in the guitar mould. Attachment : PXL_20221116_141955560.jpg 🙂🎶🙏🎸

Then plane the edges flat on the shooting board. Attachment : PXL_20221104_120832643.jpg Attachment : PXL_20221104_101554408.jpg 🎸🙏🎶🙂

Then cut into shape on the bandsaw. Attachment : PXL_20221104_094805768.jpg 🙂🎶🙏🎸