Attachment : PXL_20220929_113151658.jpg Attachment : PXL_20220916_124945432.jpg Next, glue the 4 pieces together to form the heel then glue the heel to the neck Attachment : PXL_2022122...

Attachment : PXL_20220922_143507180.jpg Attachment : PXL_20220929_101927609.jpg Once the glue has set the headstock can be planed flat to the 14mm thickness. 🙂🙏🎸
...

Attachment : PXL_20220916_111936965.jpg Attachment : PXL_20220916_111943607.jpg Once the two pieces are planed flat and square they can be glued together as shown in the pictures. The thick...

Attachment : PXL_20220916_104004285.jpg Place the two pieces of the neck into the vice as shown in this picture and plane the joint flat and square and keeping the angle of the scarf joint. Plane ...

Attachment : PXL_20220916_103726020.jpg Attachment : PXL_20220916_103733357.jpg Measure 90mm from the Nut towards the end of the headstock and mark the position of the scarf joint. I cut it...

Attachment : PXL_20220908_091021219.jpg Attachment : PXL_20220909_141913388.jpg I started by squaring up the neck blank. Planing one of the faces flat and smooth then squaring up both of th...

So here I go with Parlour N°2. It's pretty much the same as my first attempt but this time with X-bracing rather than ladder bracing. I'll try and give a wee bit more of an explanation of the process ...

@nolanrathkegmail-com You certainly can use it for fretboards. I've seen it used a couple of times. You might be lucky enough to not need to fill in any gaps but if you do I'd follow @nsj advice and u...

@dhawkes1gmail-com I agree with robin, Dan. Just mark a new centre line on the fretboard and bring the sides in evenly to match your neck profile...... double check that your neck sizes and angle are ...

@nsj Very close! Nice job. Really enjoying watching this build Neil. 🙂🎶🙏🎸

A bit of a closer look. Attachment : PXL_20230704_194308464.jpg Attachment : PXL_20230704_194327822.jpg Attachment : PXL_20230704_194345390.jpg 🎸🙏🎶ὤ...

All finished......🙌 Attachment : PXL_20230615_135408200.jpg Not quite........I forgot to put fret markers in so went back and fitted side dots Attachment : PXL_20230616_091918296.j...

Preparing bridge pin holes for strings Attachment : PXL_20230614_132246905.jpg Attachment : PXL_20230614_131703399.jpg Attachment : PXL_20230616_204801385.jpg 🎶...

Finishing.... with oil Attachment : PXL_20230609_082707009.jpg Attachment : PXL_20230607_150124532.jpg 🎸🙏🙂🎶

Saddle making Attachment : PXL_20230608_125558783.jpg Attachment : PXL_20230607_132204290.jpg Attachment : PXL_20230608_130710508.jpg Attachment : PXL_20230613_130621051.jpg ...

More nut making Attachment : PXL_20230608_092211711.jpg Attachment : PXL_20230608_121756318.jpg Attachment : PXL_20230608_100652296.jpg 🎸🙏🙂🎶

Making the nut Attachment : PXL_20230607_122616071.jpg Attachment : PXL_20230607_130139575.jpg Attachment : PXL_20230607_124600100.jpg Attachment : PXL_20230607_123802636.jpg ...

Sanding Attachment : PXL_20230602_105544045.jpg 🎸🙏🙂🎶

Leveling, crowning and polishing frets Attachment : PXL_20230531_151026106.jpg Attachment : PXL_20230601_124400443.jpg Attachment : PXL_20230601_144300693.jpg 🎶🙂&#...

Gluing on the bridge Attachment : PXL_20230525_102627463.jpg Attachment : PXL_20230525_102634606.jpg Attachment : PXL_20230525_090552766.jpg 🎸🙏🙂🎶