Then plane and scrape it flush with the sides. Attachment : PXL_20230308_090636647.jpg Attachment : PXL_20230308_092125991.jpg 🎸🙂🎶🙏

Then cutting it to size. Attachment : PXL_20230308_090515324.jpg Attachment : PXL_20230308_090345185.jpg 🙏🎶🙂🎸

Then glued it in place. Attachment : PXL_20230303_142643603.jpg Attachment : PXL_20230303_151834152.jpg 🎸🙂🎶🙏

Then I made the end graft from a cut off from the neck blank and two pieces of ebony veneer. Attachment : PXL_20230303_141452800.jpg Attachment : PXL_20230303_150623921.jpg 🙏&#x...

A wee bit of work on the end graft. Once it was marked out I gouged out the channel using chisels and "Grannies Tooth" Attachment : PXL_20230303_121010664.jpg Attachment : PXL_20230303_134...

Then I used the router and binding jig with a flush cut bit to trim the back and soundboard flush with the sides. Attachment : PXL_20230303_101356804.jpg Attachment : PXL_20230303_095651325...

Then I glued on the soundboard using the go-bar deck again. Attachment : PXL_20230302_120354103.jpg Attachment : PXL_20230302_121124041.jpg 🎶🎸🙏🙂

Then I marked out and cut out the notches to accommodate the braces of the soundboard. Attachment : PXL_20230224_115500427.jpg Attachment : PXL_20230224_115440900.jpg ......... Attach...

Next I cut out the notches in the kerfed lining to accommodate the back braces ready to glue on the back of the guitar. Attachment : PXL_20230209_142156708.jpg Then glued on the back using the ...

Then finished off using a sanding stick. Attachment : PXL_20221223_112230715.jpg Attachment : PXL_20221223_112239128.jpg ........ Attachment : PXL_20230202_134808725.jpg Attach...

Then gouged out using chisels. Attachment : PXL_20221222_152643727.jpg Attachment : PXL_20221222_152200582.jpg 🎶🎸🙏🙂

I cut out the edges using my Japanese saw. Attachment : PXL_20221222_143051515.jpg Attachment : PXL_20221222_143123547.jpg 🙂🙏🎸🎶

Next I marked out the dovetail. Attachment : PXL_20221222_141219576.jpg Attachment : PXL_20221222_141231194.jpg 🎶🎸🙏🙂

Then I had to radius the top edge and the back edge again. Attachment : PXL_20221130_153119512.jpg Attachment : PXL_20221130_154528941.jpg 🎶🎸🙏🙂

Next I glued the kerfed lining onto the edges of both sides. Attachment : PXL_20221118_130132369.jpg Attachment : PXL_20221125_110738336.jpg 🙂🙏🎸🎶

Then I cut the kerf into the strips using the kerfed lining jig on the bandsaw. Attachment : PXL_20221118_091601449.jpg Attachment : PXL_20221118_091944101.jpg 🎶🎸🙏...

Next I prepared the strips of wood for the Kerfed lining. Attachment : PXL_20221104_132319153.jpg Attachment : PXL_20221104_152410508.jpg Attachment : PXL_20221109_151125917.jpg &...

Once the sides and blocks were glued together I radiused the edges of the sides on the radius dishes. 28' for the edge to be glued to the soundboard.... Attachment : PXL_20221118_101450916.jpg ...

Then I glued them in place inside the mould Attachment : PXL_20221117_140936288.jpg Attachment : PXL_20221117_140927620.jpg 🙏🎶🎸🙂

Then I cut the end block and the heel block to size and squared them up. Attachment : PXL_20220916_144517215.jpg Attachment : PXL_20220916_143044686.jpg 🙂🎸🎶...