LOADING...
Skip to toolbar

Liked Forum Posts

RE: S-Type Necks 🎸

I’m working on sanding the radius into this fretboard today, it’s a beautiful, warm, sunny, spring day. ☀️ Attachment : CF19B4A3-F715-4CD6-B9F1-9105BA5EC530.jpeg Attachment : ...

In forum Electric

4 years ago
RE: Acoustic Bliss

Posted by: @boo Posted by: @bpower Thats like a survival pack @bpower Indeed it is. A man can’t survive without beer, snacks and bog roll. 😆 The difference being that you can only consum...

In forum Pluckers Paradise

4 years ago
RE: hello from casablanca

Welcome to the group @nossair Good looking guitar, what others have you built.

In forum New Members

4 years ago
RE: hello from casablanca

@nossair Welcome to the forum you guitar looks very good

In forum New Members

4 years ago
RE: hello from casablanca

Hello @nossair Welcome to the forum and well done building your guitars. 👍

In forum New Members

4 years ago
hello from casablanca

hello everyone i'm nossair from morocco. i already made 4 guitars thanks to you and all the information you provide on youtube. Attachment : IMG_20220413_160611.jpg

In forum New Members

4 years ago
RE: Hello from sunny Scotland

Posted by: @lionhound Built boats in the past but that’s using fat bits of wood, not the delicate kind of work that’s going to be needed here But boats are always needed in Scotland ...

In forum New Members

4 years ago
RE: S-Type Necks 🎸

This thread is turning into a body repair shop. I’ve just discovered another problem, the jack plate route is slightly too big to get both screws in so I’ll have to build up something at one end to a...

In forum Electric

4 years ago
RE: S-Type Necks 🎸

Posted by: @tv101 You don’t need to mess up another back plate - some 3mm ply* could do the job just as well? Or, use some 6mm ply* and hollow out the underside, then you don’t have to worry about s...

In forum Electric

4 years ago
RE: S-Type Necks 🎸

“It just saves a load of messing around down there”. I was always told not to mess around down there, so it’s got to be a good plan. 😉 You don’t need to mess up another back plate - some 3mm p...

In forum Electric

4 years ago
RE: S-Type Necks 🎸

What do you think @markbailey ?

In forum Electric

4 years ago
RE: S-Type Necks 🎸

I have another problem. As I am putting a trem in with a much bigger block, the springs are sitting high and proud of the back of the guitar body. I’ve been pondering over it and thought of one solut...

In forum Electric

4 years ago
RE: S-Type Necks 🎸

It’s not a bad fit now at the sides, as far as the springs are concerned. Attachment : 2A9D6776-E401-430A-87E1-994F7D2AF3BC.jpeg Attachment : 45313392-4D12-4207-9EC3-B7E98E5B98AF.jpeg

In forum Electric

4 years ago
RE: S-Type Necks 🎸

More snagging work. I’m using a trem with a bigger block so one of the springs was seriously catching on one side of the spring cavity (I forgot to take a picture). I had to get the router out again. ...

In forum Electric

4 years ago
RE: Acoustic Bliss

Posted by: @bpower Thats like a survival pack @bpower Indeed it is. A man can’t survive without beer, snacks and bog roll. 😆

In forum Pluckers Paradise

4 years ago
RE: Acoustic Bliss

@boo lol. Thats like a survival pack. 🙂

In forum Pluckers Paradise

4 years ago
RE: Acoustic Bliss

Posted by: @tv101 I like that you keep your Sizzlin’ Extra Hot Pringles in the fridge. Wise move. @tv101 Just above, on the next shelf, is the toilet roll. 😆

In forum Pluckers Paradise

4 years ago
RE: Acoustic Bliss

I like that you keep your Sizzlin’ Extra Hot Pringles in the fridge. Wise move. 🤣

In forum Pluckers Paradise

4 years ago
RE: Acoustic Bliss

@bpower and @tv101 Yeah but it’s even better if you can get your wife to buy the snacks and beer. 🙌🍟🍕🧀🌶🍺🍻 Attachment : C6B06D85-0BE3-4AFE-A7...

In forum Pluckers Paradise

4 years ago
RE: Acoustic Bliss

@tv101 I'm liking this deal. 🙂

In forum Pluckers Paradise

4 years ago
Page 216 / 1591

Russ

Profile picture of Russ

@russ

Active 6 days, 6 hours ago
Rep Points balance: 29,622
Hero Points balance: 1,544
Rank: Ninja