Then I routed out the binding channel on the top and the back. Attachment : PXL_20230316_114757822.jpg Attachment : PXL_20230316_114607223.jpg 🙏🎶🙂🎸

Next I prepared the binding for both the top and the back. Attachment : PXL_20230310_115107233.jpg Attachment : PXL_20230310_114032134.jpg I then held it in place in the mould. Attach...

Then planed and scraped it flush with the soundboard surface. Attachment : PXL_20230316_092438352.jpg Attachment : PXL_20230316_093516636.jpg 🙏🎶🙂🎸

Then glued it on. Attachment : PXL_20230315_140745113.jpg Attachment : PXL_20230315_135124324.jpg 🎸🙂🎶🙏

Then made the purfling for the top edges. Gone for simple black/white/black. Attachment : PXL_20230315_095311820.jpg Attachment : PXL_20230315_112848764.jpg 🙏🎶🙂&#...

Next I routed out the purfling channel on the soundboard. Attachment : PXL_20230310_143311712.jpg Attachment : PXL_20230310_143151037.jpg 🎸🙂🎶🙏

Then a wee bit of sanding. Attachment : PXL_20230308_094309064.jpg 🙏🎶🙂🎸

Then plane and scrape it flush with the sides. Attachment : PXL_20230308_090636647.jpg Attachment : PXL_20230308_092125991.jpg 🎸🙂🎶🙏

Then cutting it to size. Attachment : PXL_20230308_090515324.jpg Attachment : PXL_20230308_090345185.jpg 🙏🎶🙂🎸

Then glued it in place. Attachment : PXL_20230303_142643603.jpg Attachment : PXL_20230303_151834152.jpg 🎸🙂🎶🙏

Then I made the end graft from a cut off from the neck blank and two pieces of ebony veneer. Attachment : PXL_20230303_141452800.jpg Attachment : PXL_20230303_150623921.jpg 🙏&#x...

A wee bit of work on the end graft. Once it was marked out I gouged out the channel using chisels and "Grannies Tooth" Attachment : PXL_20230303_121010664.jpg Attachment : PXL_20230303_134...

Then I used the router and binding jig with a flush cut bit to trim the back and soundboard flush with the sides. Attachment : PXL_20230303_101356804.jpg Attachment : PXL_20230303_095651325...

Then I glued on the soundboard using the go-bar deck again. Attachment : PXL_20230302_120354103.jpg Attachment : PXL_20230302_121124041.jpg 🎶🎸🙏🙂

Then I marked out and cut out the notches to accommodate the braces of the soundboard. Attachment : PXL_20230224_115500427.jpg Attachment : PXL_20230224_115440900.jpg ......... Attach...

Next I cut out the notches in the kerfed lining to accommodate the back braces ready to glue on the back of the guitar. Attachment : PXL_20230209_142156708.jpg Then glued on the back using the ...

Then finished off using a sanding stick. Attachment : PXL_20221223_112230715.jpg Attachment : PXL_20221223_112239128.jpg ........ Attachment : PXL_20230202_134808725.jpg Attach...

Then gouged out using chisels. Attachment : PXL_20221222_152643727.jpg Attachment : PXL_20221222_152200582.jpg 🎶🎸🙏🙂

I cut out the edges using my Japanese saw. Attachment : PXL_20221222_143051515.jpg Attachment : PXL_20221222_143123547.jpg 🙂🙏🎸🎶

Next I marked out the dovetail. Attachment : PXL_20221222_141219576.jpg Attachment : PXL_20221222_141231194.jpg 🎶🎸🙏🙂