Hello Guys! I am new here on this platform because this is one of the best platform for guitar knowledge.

Thank you for sharing your ideas. Here I have learned a lot of things from this post and appreciate your innovative thinking.

Attachment : PXL_20221125_155929560.jpg Attachment : PXL_20221125_155853912.jpg Then each brace has a 28 foot radius planed onto the edge that will be glued to the soundboard. 🙏&#x...

Attachment : PXL_20221118_142252461.jpg Attachment : PXL_20221118_155312102.jpg Next, I prepared the braces for the soundboard. For this guitar the braces on the upper bout are 10mm thick a...

Attachment : PXL_20221222_095440788.jpg Attachment : PXL_20221222_094417613.jpg Then cut out the soundboard shape on the bandsaw. 🙂🙏🎸🎶

Attachment : PXL_20221005_125759501.jpg Attachment : PXL_20221005_125856592.jpg Then plane and sand it flush with the soundboard Attachment : PXL_20221007_130614233.jpg 🎶
...

Attachment : PXL_20220930_133129961.jpg Attachment : PXL_20220930_140353758.jpg Then glue in the rosette. 🙂🙏🎸🎶

Attachment : PXL_20221221_132945854.jpg Attachment : PXL_20221221_132919780.jpg Cut some strips of laminate for the construction of the rosette. They are 3-4mm wide and about 30-50mm longer...

Attachment : PXL_20220928_142749065.jpg Attachment : PXL_20220928_145040608.jpg Plane the soundboard down to a smooth and level 3mm thickness. 🙂🙏🎸🎶

Attachment : PXL_20220922_132840858.jpg Attachment : PXL_20220922_102222195.jpg Making the soundboard next. Two pieces of rough sawn bookmatched spruce. Plane along the bookmatched edges th...

yep, I picked up a router template set, so that should help, but never underestimate the level of my ineptitude 😉 Thank you for the pointer as far as the Gotoh - I’ll definitely keep that in mind for ...

@swepri thank you for your suggestion. I really don’t know why I didn’t think of that myself! My old garden bench is in the workshop waiting to be up cycled into something, so I’ve got loads of cheap,...

@swepri yes, that's exactly what I am thinking - especially if you compare to a zero fret! I don't think my jig does this and I notice that difference on yours is quite pronounced? Anyway, thank you s...

@steveh musiclily do a decent routing template, only thing missing is the recess for the floyd but that's not to hard to knock up. I'd recommend grabbing a gotoh floyd, 150 ish but fantastic units....

Well you're cutting the standard fret slot where the nut goes anyway, the jig usually has it as one of the notches to line up so in theory that already happens. Certainly never had a problem yet mysel...

So after introducing myself to a very friendly welcome I thought I would try and ask a question. I can’t work out whether this is the correct forum, but here goes… I have one of those fret jigs for ...

Attachment : PXL_20230428_105125703.jpg Attachment : PXL_20230428_105604681.jpg Then cut the fret slots with the fretting jig 🙏🎶🙂🎸

Attachment : PXL_20230428_125701251.jpg Attachment : PXL_20230428_132541803.jpg Once the slots were cut I tapered the fretboard using a shooting board and plane. It is 46mm at the nut and 5...

Attachment : PXL_20230428_092631730.jpg Attachment : PXL_20230428_092728845.jpg Once I got the fretboard blank thickness I squared off one edge. I then used this edge to mark out the fret p...

Attachment : PXL_20230426_141549382.jpg Attachment : PXL_20230421_144526277.jpg A bit of fretboard making next. Prepare the fretboard blank by planing one surface smooth and flat. Plane the...