Building my own version of a strat this time, 3 single coils, 5 way blade etc. So far I've been working on the neck, today I got the fret markers done. Next will either be frets in or carve, haven't d...

Cheers @swepri The shooting board has a series of holes at even intervals along the length of the board. I think mine were set at 8cm apart and about 3cm back from the edge (it's hiding in the back of...

......then glued it onto the inside of the back Attachment : PXL_20230202_133942215.jpg 🙏🎶🙂🎸

Attachment : PXL_20230202_112347273.jpg Attachment : PXL_20230202_115436639.jpg I used an off cut from the soundboard to make the centre strip for the back 🎸🙂🎶Ƕ...

Then I plane on the radius of 20 foot using the shooting board. Attachment : PXL_20221222_111323781.jpg Attachment : PXL_20221222_111206068.jpg 🎸🙂🎶🙏

Attachment : PXL_20221221_132129470.jpg Planing down the back braces flat and square. They are all 7mm thick and will eventually be 14mm high but I'm leaving them 20mm high for now. 🙏
...

Attachment : PXL_20220929_152744833.jpg Joining the back. I'm using cherry for this one. 🙏🎶🙂🎸

Attachment : PXL_20230216_115948488.jpg Next, I glued on the X-brace and the Upper Bout braces. 🙂🎶🎸🙏

Well I got there in the end, plays really nice, looks really nice and sounds really nice. I'll call that a win. Attachment : 20230727_195323-01.jpeg Attachment : 20230727_195333-01.jpeg ...

Well I finally got the finish on, I cleaned up the fretboard etc but think I'll let it sit another day before assembly. Attachment : 20230725_230832-01.jpeg Attachment : 20230725_230853.j...

Attachment : PXL_20230203_151257063.jpg Attachment : PXL_20230202_141558050.jpg Then made the bridge plate using "harvested" wood from the back. 🙂🎸🎶🙏

Attachment : PXL_20221222_120207311.jpg Then using some "harvested" wood from the soundboard, I made the soundhole plate Attachment : PXL_20221222_131029286.jpg Attachment : PXL_2022122...

Attachment : PXL_20230216_111453791.jpg Attachment : PXL_20230216_101527375.jpg The next stage was to partially carve the ends of the other Top Braces prior to gluing them in place as it ca...

Next was clean up the glue squeeze out and start making some center seam diamonds. Just like all my other guitars I enlisted the help from my daughter. I love getting her involved. You never know... s...

Hi Everyone, Just wanted to post my second guitar. Finished it up and gave it to a friend. Could not have done it without Mark's courses and the advice from the community. On to #3... (Hopefully I'l...

Attachment : PXL_20221118_142252461.jpg Attachment : PXL_20221118_155312102.jpg Next, I prepared the braces for the soundboard. For this guitar the braces on the upper bout are 10mm thick a...

A bit of a closer look. Attachment : PXL_20230704_194308464.jpg Attachment : PXL_20230704_194327822.jpg Attachment : PXL_20230704_194345390.jpg 🎸🙏🎶ὤ...

All finished......🙌 Attachment : PXL_20230615_135408200.jpg Not quite........I forgot to put fret markers in so went back and fitted side dots Attachment : PXL_20230616_091918296.j...

Preparing bridge pin holes for strings Attachment : PXL_20230614_132246905.jpg Attachment : PXL_20230614_131703399.jpg Attachment : PXL_20230616_204801385.jpg 🎶...

Finishing.... with oil Attachment : PXL_20230609_082707009.jpg Attachment : PXL_20230607_150124532.jpg 🎸🙏🙂🎶