Attachment : PXL_20230428_125701251.jpg Attachment : PXL_20230428_132541803.jpg Once the slots were cut I tapered the fretboard using a shooting board and plane. It is 46mm at the nut and 5...

Attachment : PXL_20230428_105125703.jpg Attachment : PXL_20230428_105604681.jpg Then cut the fret slots with the fretting jig 🙏🎶🙂🎸

Attachment : PXL_20230428_092631730.jpg Attachment : PXL_20230428_092728845.jpg Once I got the fretboard blank thickness I squared off one edge. I then used this edge to mark out the fret p...

Attachment : PXL_20230421_140633910.jpg Attachment : PXL_20230421_140653945.jpg Peg holes for the machine heads drilled 🙂🎶🎸🙏

Attachment : PXL_20230426_141549382.jpg Attachment : PXL_20230421_144526277.jpg A bit of fretboard making next. Prepare the fretboard blank by planing one surface smooth and flat. Plane the...

Attachment : PXL_20230330_092721967.jpg Attachment : PXL_20230330_101440484.jpg Cut off the wings and carve the rest of the neck Attachment : PXL_20230330_103458420.jpg Attachment...

Attachment : PXL_20230324_131908383.jpg Attachment : PXL_20230324_135421592.jpg Then got on with a bit of carving Attachment : PXL_20230329_143542314.jpg Attachment : PXL_2023032...

Attachment : PXL_20230329_105719400.jpg Next, I marked out the velute.... Attachment : PXL_20230329_125852711.jpg Attachment : PXL_20230330_091821640.jpg ...and roughly carved out th...

Attachment : PXL_20230323_100806246.jpg Attachment : PXL_20230323_135707969.jpg Attachment : PXL_20230324_115654487.jpg Attachment : PXL_20230323_141840032.jpg Next, I roughly...

Attachment : PXL_20230322_153249154.jpg Attachment : PXL_20230322_143452017.jpg Next I marked out the dovetail onto the heel end of the neck. Attachment : PXL_20230323_093612635.jpg ...

Attachment : PXL_20230322_093207624.jpg Attachment : PXL_20230322_101104810.jpg Plane down the edges of the veneer flush with the headstock and cut the edge of it straight against the front...

Attachment : PXL_20230317_112131444.jpg Attachment : PXL_20230317_112551504.jpg Attachment : PXL_20230317_112202764.jpg Then I glued the veneer onto the headstock. Clamp it down, app...

Attachment : PXL_20230302_135042668.jpg Attachment : PXL_20230302_134309860.jpg Next, I prepared the headstock veneer. Planed and scraped it smooth to a thickness of 2mm.

Attachment : PXL_20230309_140313579.jpg Attachment : PXL_20230309_113146313.jpg Attachment : PXL_20230309_140619152.jpg Next, I routed out the truss rod channel. The access for this ...

Attachment : PXL_20220929_113151658.jpg Attachment : PXL_20220916_124945432.jpg Next, glue the 4 pieces together to form the heel then glue the heel to the neck Attachment : PXL_2022122...

Attachment : PXL_20220916_111936965.jpg Attachment : PXL_20220916_111943607.jpg Once the two pieces are planed flat and square they can be glued together as shown in the pictures. The thick...

Attachment : PXL_20220916_103726020.jpg Attachment : PXL_20220916_103733357.jpg Measure 90mm from the Nut towards the end of the headstock and mark the position of the scarf joint. I cut it...

Attachment : PXL_20220908_091021219.jpg Attachment : PXL_20220909_141913388.jpg I started by squaring up the neck blank. Planing one of the faces flat and smooth then squaring up both of th...

Welcome to the forum, I’m looking forward to seeing what you will be building. Enjoy the journey 👍 Sounds like there’s quite a few of us scattered around Scotland, I’m on the northeast coast n...

@peter-c-f. Welcome Peter. The course in Glasgow is a great start to guitar building. I hope you are successful getting a place. I completed the NQ course and came away with a couple of parlour guitar...