LOADING...
Skip to toolbar

Liked Forum Posts

RE: Implausibly difficult side bend - Done!

Beautiful work @markbailey, I hope you and Carol are well!

In forum Acoustic

5 years ago
RE: Implausibly difficult side bend - Done!

Looking great @markbailey I miss that workshop view, the live streams were lockdown therapy. I hope you're doing ok, best to Carol.

In forum Acoustic

5 years ago
RE: Jigs, patterns, and lines on paper

@robin Yep, that's the plan. Yesterday I also corrected the guide fence on my band saw by shimming one edge of the locking bar with some masking tape. I'll do a test cut on some scrap to make sure it'...

In forum Electric

5 years ago
RE: Jigs, patterns, and lines on paper

Neck blank arrived today. Looks decent. Now I just need to rip it in half and I should be able to start working on it very soon. Attachment : 20210914_183152.jpg Also, I made the router base pl...

In forum Electric

5 years ago
RE: Robin's build #002

All l can do is black inkjet waterslide and that took a lot of trial and error, I've got enough for my next four builds though. I tried colour too, but it was too see through. All that trial and erro...

In forum Electric

5 years ago
RE: Facets

One thing about the neck is that the transition up to the headstock sort of begins between the 1st and 2nd frets. I know 1st fret is the standard but it feels quite comfy in my hands as is. Has anyone...

In forum Guitar ER - When Guitar Builds Go Bad

5 years ago
RE: Facets

Just need to tidy up that heel transition with the surform and use progressively finer grits all over. One thing about the neck is that the transition up to the headstock sort of begins between the 1s...

In forum Guitar ER - When Guitar Builds Go Bad

5 years ago
RE: Robin's build #002

Your certainly my goto logo man @robin. Very nice. 🙂🎸🎶🙏

In forum Electric

5 years ago
RE: In the beginning we mark the nut...

I’ve used a round file before. I use a really fine, thin, round file @boo I’ll have to look at the type of file you’re talking about, I have a half round mini file that might to, between that, @rock...

In forum Electric

5 years ago
RE: In the beginning we mark the nut...

clean out the finish build up from post holes by running a sharp knife carefully round the inside @rocknroller912 thanks for the idea, i think the initial layers will be cured hard by now, I can test...

In forum Electric

5 years ago
RE: In the beginning we mark the nut...

One thing I would advise though is that you mask up the neck pocket at least, @boo yeah I figured that a few coats in, masked it up and then started removing it between coats as it was building up a ...

In forum Electric

5 years ago
RE: In the beginning we mark the nut...

@tej For stuff like that, I’ve used a round file before. I use a really fine, thin, round file (a chainsaw sharpening file). Be careful just to push the file down into the hole and along the top edge ...

In forum Electric

5 years ago
RE: In the beginning we mark the nut...

@tej Its possible to clean out the finish build up from post holes by running a sharp knife carefully round the inside. I know this sounds scary but the knife will take paint off without damaging the ...

In forum Electric

5 years ago
RE: Robin's build #002

Couldn't resist a little trial fit of the tuners @robin Looking good Robin, I’ve done the same thing with a truss rod cover before. Every day is a school day eh? 😁👍

In forum Electric

5 years ago
RE: In the beginning we mark the nut...

Progress on the body finish @tej It’s looking superb. One thing I would advise though is that you mask up the neck pocket at least, it doesn’t matter too much about the pickup cavities. 👍

In forum Electric

5 years ago
RE: In the beginning we mark the nut...

Progress on the body finish Attachment : 14C657EB-30F3-4520-9B4C-DB394F56A706.jpeg

In forum Electric

5 years ago
RE: Handmade jigs and tools

Already thought of the dust extraction @robin. If I hadn't broken my hole saw I would have done it. It will have one but for now I just could wait to try it out. 🙂

In forum Acoustic

5 years ago
RE: Hello from NI

Hello there @stephen, sounds like you’ve already gotten great advice and encouragement. This is a super cool place to be, welcome!

In forum New Members

5 years ago
RE: Facets

Posted by: @ Turned out fine in the end, thanks! 🙂

In forum Guitar ER - When Guitar Builds Go Bad

5 years ago
RE: Hello from NI

I'm *just* manly enough to go into Screwfix 🙂 I don't want to get laughed out of a lumber yard for building a guitar and not a house 😉 @stephen No, don’t think like that. The lumber y...

In forum New Members

5 years ago
Page 288 / 939

Robin

Profile picture of Robin

@robin

Active 5 months, 1 week ago
Rep Points balance: 17,152
Hero Points balance: 237
Rank: Knight