Liked Forum Posts
|
RE: Designing my own neck tru guitar it will be rubbing on the side on the nut slot which isn’t good for tuning. @rocknroller912 Well on a Les Paul, none of the strings are ligning up with the nut. You just have to cut the nut with a l... |
In forum Electric |
5 years ago |
|
RE: Designing my own neck tru guitar @koendb I think that moving the peg hole may cause an alignment problem with the nut as the string won’t be pulling in a straight line, it will be rubbing on the side on the nut slot which isn’t good ... |
In forum Electric |
5 years ago |
|
RE: Designing my own neck tru guitar You could plug the hole and drill again where you wnt it. If you don't move it too far, the washer will cover the repair @Robin Yes indeed. I 'll decide that just before final sanding and finishi... |
In forum Electric |
5 years ago |
|
RE: Replacing acoustic bridge….. Hi Bill, I have never had to remove a bridge but, if I did, I absolutely agree with @rocknroller912. If there is no reason to reuse the existing bridge then planing or routing it off will do far less ... |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Designing my own neck tru guitar Today, I testfitted the tuners and discovered a small design flaw in my headstock. I should have left a bit more space on a few pegholes, they are rather close to the edge, and, the one for the G stri... |
In forum Electric |
5 years ago |
|
RE: Hello ya'll; In for the long haul @russ, @mattbeels, @Boo, @Koendb, @rocknroller912, (@russ),@tv1, @russ, @mattbeels, @Boo, @Koendb "Man, it's not as easy as it looks on Youtube, fer sure fer sure...You folks make it look EASIER;" i k... |
In forum New Members |
5 years ago |
|
Replacing acoustic bridge….. My acoustic has a problem - there are two splits in the bridge at either end and in front of the saddle. The guitar is an Ashton, Australian make, China built. It was a 50th birthday present from the... |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Replacing acoustic bridge….. @frocesterbill Repairs like this are mostly what I do rather than new builds, so here is my suggestion although I’m open to being told I’m wrong. Recently I’ve done two bridge removals one for the loc... |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Replacing acoustic bridge….. @Rocknroller912 Thanks for that - sounds like a plan - I wondered about heat to soften glue but as you say as the bridge is not being reused then carefully remove/destroy……….. |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Jazz Bass Paint Job (Chameleon) I'm glad it got to you. I've got no idea where I plucked the wrong address from. I wonder who's address that is then. @robin It was actually quite similar and one that people have said before. It hap... |
In forum Finishing |
5 years ago |
|
Router sled base Coffee tables make good router sled bases 👍 Attachment : 530FCC18-DAD6-4C9E-838B-F7CCFC047EB4.jpeg |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Jazz Bass Paint Job (Chameleon) @robin Just so you know Robin, you got the address wrong but my name and post code were correct so it got here. 😁🤘 Thanks again. |
In forum Finishing |
5 years ago |
|
RE: It's a matter of TRUSS!!! Understood...thanks Mark Will carry on but promise to keep the wig locked away!!!!! |
In forum Acoustic |
5 years ago |
|
RE: It's a matter of TRUSS!!! Don't go tightening the truss rod it after you glue the fillet or it will bend and break the fillet! Also - when the fretboard is glued on the neck will be far too stiff for the truss rod to work, so ... |
In forum Acoustic |
5 years ago |
|
RE: It's a matter of TRUSS!!! Hey @markbailey Thanks so much for the reply, really appreciate it and so good to hear from you... I'll crack on, BTW, if I didnt mention it before the acoustic course is so good...so clear... hope to... |
In forum Acoustic |
5 years ago |
|
RE: In the beginning we mark the nut... Apologies to all for radio silence, not a lot to post about while I’m applying coat after coat of finishy coloury gloop, it’s all just more green than it used to be 🙂 As for the headstock logo... |
In forum Electric |
5 years ago |
|
RE: Jazz Bass Paint Job (Chameleon) These arrived today in the post. Thanks very much @robin much appreciated. I’ll get it built up as soon as I’ve flow coated the paint job and polished it. Attachment : 006037F1-BA23-4046-8A67-838... |
In forum Finishing |
5 years ago |
|
RE: It's a matter of TRUSS!!! Thanks to everyone for chipping in - good Q!...Short answer - It's OK. 😌 Some things to consider: The Aluminium part does look like it could sit squarer...make sure the round bar is fully in ... |
In forum Acoustic |
5 years ago |
|
It's a matter of TRUSS!!! Hey Guys This is a shout out to Mark and all of the acoustic builders..I've made a little video about the truss rod dilemma I have and something I would like to understand before I carry on. So it's a... |
In forum Acoustic |
5 years ago |
|
RE: It's a matter of TRUSS!!! @steveadams. Sorry Steve. I'm no expert in this at all. There is some angle on the neck but I'm not sure that it is as much as it seems in your video. I would expect that the wee barrel nut on the end... |
In forum Acoustic |
5 years ago |