The soundboard board is routed now and maple binding glued in. Definitely out of my comfort zone doing that. We'll see what tomorrow brings when I take the tape off and clean it up, maybe I'll do the ...

Although I happy with the good close glue join that I've got between the sides and soundboard/back, it just doesn't look finished without binding. Having said that, I'm reluctant to set about it with ...

Fretboard levelled and dots added now. I went to get my dots out of my bag of bits for this build, and realised that I hadn't bought any. So I cut some 6mm plugs from a piece of maple an used that. Al...

Thats the neck/body joint done, fretboard glued, the neck carved and dry fitted. Doesn't sound much when you say it quickly, but its certainly a challenge getting the neck/body joint without gaps, on...

I've made my bridge now, that's a fun wee project in its own. Took me about 6 hours to do what @markbailey does in his 35 minute video, but just follow the instructions and it happens. Photos of its v...

Nice work @robin. Those little diamonds are a very common way to support the crack but I've just recently heard about the use of Japanese paper, pasted along the inside of the crack. It tends to be us...

I shaped the soundboard seam diamonds today and glued them in. I also put them along the repaired crack in the soundboard, it might affect the sound qualities, but I doubt if I'll notice it. Attach...

I've trimmed the back braces to length and notched the kerf lining and got the back fitting fairly good. I've dry clamped it with the 6 metres of rubber band that I've cut from an old inner tube, it's...

The back kerf lining is on now. Merry xmas to you all. Attachment : 20231224_175645.jpg

Attachment : 20231223_164645.jpg Sides now glued to the front, and the back edges shaped ready for the kerf lining. Attachment : 20231223_153045.jpg Attachment : 20231223_153013.jpg ...

Shiny shiny ✨✨✨✨ Attachment : VID_20231204_110646.mp4

Slippery top? Attachment : VID_20231205_103114.mp4

I’ve got all the butterflies in, sanded everything and applied some Danish Oil, 3 coats so far. Not a bad finish that, for a work bench. I might give it one more coat for good measure. Attachment ...

Used a small router to hog out the majority to the waste, then fine cut the rest out with chisels. Glued one in and left it overnight. I’ll plane it down today and sand it flush. Attachment : IMG...

Made my butterflies in inlay along the joint. Attachment : IMG_20231119_142651_resized_20231120_103550803.jpeg Attachment : IMG_20231118_155506_resized_20231120_103551820.jpeg Attach...

Used a straight edge and my circular saw to cut a groove for the Cherry strip. Attachment : IMG_20231116_144236_resized_20231120_103422232.jpeg Attachment : IMG_20231116_144224_resized_202...

After glueing together the the two main pieces for the top, there were a couple of places where there hadn’t been a full coming together of the two faces. I could see that over time this could become ...

I’ve finally got completely fed up of using wonky, cobbled together, sagged in the middle, unflat so-called work benches. I’m finally building a half decent but solid woodworking bench, it’s not the b...

Sanded the kerfed edge of one side while the glue on the other side was drying. I found it far too flexible to hold it in shape out of the mold, so clamped it into the mold, so much easier. Attachm...

Finally got the first coat of finish on the body, and added my mates logo to the back of the headstock. Chris Mckean Music Attachment : 20231218_015537 (1).jpg Attachment : 20231212_151430....