Liked Forum Posts
|
RE: Acoustic build #2 (wife's guitar) Kits are great as a confidence builder. It also allows you to start building without having all the needed tools or skills.No argument with regards to quality of any kit is relevant, because, even if ... |
In forum Acoustic |
5 years ago |
|
RE: Acoustic build #2 (wife's guitar) @bpower kits are great but it’s satisfying to do basics the hard way too |
In forum Acoustic |
5 years ago |
|
RE: ?Luthier Jokes and Funny Stories? Attachment : 205862154_155425433314707_720471985942334843_n.jpg |
In forum Pluckers Paradise |
5 years ago |
|
RE: In the beginning we mark the nut... @robin thanks, I’ve made both horns a bit thinner now too so the lower one doesn’t block things, it’s a little annoying still but overall I’m not going to spend “that” much time at the 24th anyway! Wi... |
In forum Electric |
5 years ago |
|
RE: In the beginning we mark the nut... @koendb I always wear a strap with the guitar quite high so I can have the neck at a high angle so there’s no strain on my wrist. On the rare occasion I don’t use a strap I’ll have it one my left leg ... |
In forum Electric |
5 years ago |
|
RE: In the beginning we mark the nut... @tej I have the same issue with one of my builds. the cutaway should be a lot lower. It is also difficult to balance on my lap because of the weird curve at the bottom of the lower horn. It looks lik... |
In forum Electric |
5 years ago |
|
RE: In the beginning we mark the nut... You could almost be fooled into thing this Is going to be a guitar. I’ve got a small design flaw on my part, the lower horn, despite taking more of the thickness out is still in the way at the last fe... |
In forum Electric |
5 years ago |
|
RE: In the beginning we mark the nut... @robin turns out that I needed very little in terms of carving for the belly and wrist carves so they’re both quite slight. In might need to carve the lower horn out a little more to allow better acce... |
In forum Electric |
5 years ago |
|
RE: Inlays/marquetry @tej Will give that a try this afternoon and let you know if it works |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Inlays/marquetry @rocknroller912 could you use some tool wax on it, presuming the result would be sanded it should cause issues? |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Inlays/marquetry Nice @rocknroller912! |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Inlays/marquetry First attempt at making a sound hole ring cut from a flat sheet salvaged from the off cuts of acoustic sides and joined together. After it was scraped down I decided that it needed purfling either sid... |
In forum Guitar Building Tricks and Tips |
5 years ago |
|
RE: Neck pocket alignment @tej I wouldn’t worry about 0.5mm as long as all 6 strings line up with the pick up pole pieces. To make a thin shim start with a bit longer than you need and clamp it down. Mark the size you need and... |
5 years ago | |
|
RE: Acoustic build #2 (wife's guitar) The neck is roughed out. Now on to the body. 🙂 Attachment : 20210621_202849.jpg Attachment : 20210622_194350.jpg Attachment : 20210622_204740.jpg Attachment : 20210622_203924.... |
In forum Acoustic |
5 years ago |
|
RE: Neck pocket alignment I think given the error being quite small a slightly offset bridge will be preferable to laminating the socket and rerouting it as I think that has more likelihood of going horribly wrong. If it is j... |
5 years ago | |
|
RE: Neck pocket alignment So I’m a little less concerned about this now, in terms of the fretboard and the strings running parallel to the edges it lines up fairly close, the bridge will need to be maybe .5mm off the centre li... |
5 years ago | |
|
RE: Neck pocket alignment @koendb set neck, not sure how I’d go about making a shim thin enough! Anyway I should check it against the path of the strings and bridge first and check how big the problem is, sorry, should have do... |
5 years ago | |
|
RE: Neck pocket alignment what are my options to correct that, if any? If the neck pocket is not straight, you can shim and reroute if needed. Is it a bolt-on or set neck? |
5 years ago | |
|
Neck pocket alignment So after putting some straight edges either side of the fretboard with the neck in the socket it’s a few mm off centre at the bridge, plan today is to temporarily put the nut on and run threads for th... |
5 years ago | |
|
RE: In the beginning we mark the nut... More routing and rounding, also have the holes for the wiring, socket and strap pins done (no pic of that bit!) Onto carving next, happy days. 🙂 Attachment : 7CB47523-BFA6-4DF5-9B80-B0E300... |
In forum Electric |
5 years ago |